Ure Seal H20 - Water Based - Enhancing - Joint Stablizing - Premium Sealer
Ure Seal H20 - Water Based - Enhancing - Joint Stablizing - Premium Sealer
Ure Seal H20 - Water Based - Enhancing - Joint Stablizing - Premium Sealer
Ure Seal H20 - Water Based - Enhancing - Joint Stablizing - Premium Sealer
Ure Seal H20 - Water Based - Enhancing - Joint Stablizing - Premium Sealer
Ure Seal H20 - Water Based - Enhancing - Joint Stablizing - Premium Sealer

Ure Seal H20 - Water Based - Enhancing - Joint Stablizing - Premium Sealer

Regular price $245.00 Sale


Quantity: Out of stock.

WE ARE CURRENTLY OUT OF URE-SEAL H20. Please check out our alternative product: SUREBOND 6725 CLICK HERE

URE-SEAL H2O – Gloss is a 2-part water reducible, crystal clear Urethane. It is a high performance clear coating that can be used inside or out to protect and enhance any properly prepared concrete, pavers, or decorative concrete surface for years of service. All available in natural finish.

Pallet Pricing Available: Call 630-485-5763





USE: ICT Ure-Seal H2O is a 2-part environmentally friendly water reducible, crystal clear, alaphatic urethane. It is a high performance clear coating that can be used inside or out to protect and enhance any properly prepared concrete surface for years of service.

DESCRIPTION: ICT Ure-Seal H2O has excellent abrasion and chemical resistance with a gloss or natural finish (Keep in mind that the ‘Gloss’ blend will appear as semi-gloss when applied on brick pavers). The mild odor makes it ideal for interior applications. Ure-Seal H2O will not yellow and will form a very hard protective coating for high traffic areas, counter tops, restaurants, decorative concrete & brick pavers. Ure-Seal H2O can be used over epoxy flooring, garage floors, anywhere that high durability and superior chemical resistance is required.

SURFACE PREPARATION: 1. Clean surface thoroughly with ICT’s Total Klean (710) all purpose degreaser and cleaner to remove dirt and oils. It is recommended that you also use a bleach/liquid chlorine solution to remove any visible or microscopic algae or mildew. Rinse thoroughly. 2. If you are applying Ure-Seal over brick pavers it is recommended that you use ICT’s Total Prep (720) according to product directions. This will help remove any efflorescence and condition / prep the pavers. 3. Pressure wash the entire area thoroughly to remove any residual chemicals.

MIXING RATIO’S: ICT’s Ure-Seal is a 2 component product that comes pre-packaged in 1 Gallon and 5 Gallon kits. If not all the product in the kit is needed Ure-Seal can be mixed by using 4 parts of “Part A” and 1 part of “Part B” (i.e.: 4 quarts of Part A to 1 quart of Part B) Do not mix more material than can be used in a 2-3 hour period. Once components A and B are mixed the pot life is approximately 2-3 hours. Pot life will vary based on weather conditions, temperature, humidity etc. Mixed product should NEVER be stored in a closed container. Do not intermix different batch numbers.

DILUTION RATIO’S: Brick Pavers with sand joints: It is recommended you apply a penetration coat as your first coat. Mix Part A and Part B at the 4:1 ratio. Dilute that solution with up to 2 parts of water. (i.e.: if you have mixed a total of one gallon of product add up to 2 gallons of water) The second coat should be mixed with 1 part water. If additional coats are needed mix at the same 1 part water to 1 part Mixed Ure-Seal. Travertine: Mix Part A & Part B to the 4:1 ratio. Dilute mixture 1:1 with water (151 Natural UreSeal) 2:1 with water (150 Gloss UreSeal) Apply 1-2 coats. Note: Surface may become slippery. Use ICT Non-Skid Broadcast Blend (495) to aid in slip resistance. Acrylic Overlays (ICT TK2000 w/ Integral Color), Stamp Overlays, Acid Stains: Mix Part A and Part B at the 4:1 ratio. Dilute that solution with 1 part water. (i,e:1 gal of mixed product diluted with 1 gal of water) The second coat should be applied full strength. Additional coats may be applied to achieve a higher gloss or if additional film thickness is needed for high traffic areas. Top Coat Sealers (ICT Color Seal H2O Pro, Texture EEZ 3000) and Epoxy Floor Systems should be sealed with Ure-Seal near full strength. Counter Tops & Industrial Application: Contact ICT for additional information.

APPLICATION: ICT Ure-Seal H2O is a two component product. Mix using a low speed drill or jiffy mixer for 1-2 minutes. If dilution is recommended, mix parts A & B before and after water is added. Do not whip air into the mixture. Apply with a sprayer or short nap roller. (rolling is only recommended for indoor applications) Do not apply too thick or bubbles will form. If a second coat is required, it must be applied after the initial coat is dry to touch and visually clear, usually within 3-6 hours, but before it cures completely, usually within 24-36, hours after the initial coat is applied. Brick Pavers or Hot Surfaces should be slightly dampened with a light mist of water prior to applying Ure-Seal. Do Not Over Hydrate. Hydrate surface only if conditions allow for adequate dry/curing time. Thin pavers with a sand bed should be thoroughly dry before applying Ure-Seal H2O. The use of a quality pump up sprayer/continuous sprayer is recommended . A moderate amount of material should be applied. Do not allow Ure-Seal to puddle. If puddling occurs use a dry roller to “back roll” the material to maintain an even thickness. If you use a roller for the application of Ure-Seal use a 1/4” nap or Micro Fiber roller cover. For dry rolling/ back rolling you will need a 3/4-1” roller cover. If you should see roller marks as you are applying, lightly mist those areas with water. This will allow Ure-Seal to settle and form a more even film. Rolling is never recommended on brick pavers or travertine. Travertine should be sealed with 1-2 coats of Ure-Seal using the recommended mixing & dilution ratios. Broadcast ICT Non-Skid Broadcast Blend (495) while Ure-Seal is curing to reduce slipperiness.

Always Apply a Test Area For Best Results.

COVERAGE: Approx-200 –300 sq. ft. per gallon. Coverage rates will vary depending on substrate, textures, porosity, and application methods.

  • DO NOT apply Ure-Seal H2O when air or surface temperature is below 55°F or is expected to fall to the point before application is dry. Low temperatures and high humidity will effect drying and curing times.
  • DO NOT apply Ure-Seal H2O to new cement, mortar, grout, brick pavers, or overlays. ICT recommends a minimum wait time of 28 days, to allow these products to cure, before sealing. When sealing brick pavers, refer to manufacturer’s recommendation for wait/cure time before sealing. ICT Total Prep should be used for the removal of efflorescence prior to application of Ure-Seal H2O.
  • DO NOT apply to thin pavers if moisture is present.
  • DO NOT apply to non-porous surfaces, such as tile.

LIMITATIONS: Must be stored in air tight container to prevent evaporation and contamination with foreign material. Do not apply when surface and air temperatures are above 100o F or below 55°F or when dew point is within 5°F of air temperature. Any mixed material if not used within 1-3 hours of mixing should be discarded, this time may be increased by keeping the material in a cool dry place. Do not re-lid product once mixed as product will expand. Do not freeze, store above 40°F. If re-coat time is exceeded surface must be lightly abraded prior to applying second coat.

PRECAUTIONS: Keep out of reach of children. Applicator should wear protective eyewear and gloves. Do not take internally. Do not store in direct sunlight or excessive heat. Keep from freezing. Refer to the MSDS for this product for safety recommendations related to working with this product. Do not allow this product to freeze. Do not apply if surface is below 50°F or above 100o F. Do not apply over surfaces that have been previously sealed with a solvent based sealer unless a compatability test is performed. Use caution when applying to thin pavers or travertine when a salt water pool is in use to avoid possible maintenance issues.

  • Shelf life: 1 year @ 77°F
  • Hot tire resistance: Excellent
  • Pot life after mixing: 1-3 Hrs. @ 77°F





Welcome to the Loyalty Points Demo Store :-)

Sign up and receive 5000 pts to test out in our Store.

Earning and redeeming Reward Points

Earns you
Redeems to

Ways you can earn

  • Product Purchase
  • Refer a friend
  • Share on social media

Learn more about our program

Net Orders Checkout

Item Price Qty Total
Subtotal $0.00

Shipping Address

Shipping Methods