Surebond 6000 - Wet Look Sealer (Sample Pint)
Quantity: Out of stock.
- Deeply Enhances Surface Tone with Satin Finish
- Protects Surface by Resisting Water, Stains & Salt
- Promotes Easier Cleaning & Maintenance
- Low VOC Formula
- Breathable, Immediate Application Water Based Sealer
SB-6000 Wet Look Sealer is a proprietary water-based, modified latex, exterior quality sealer. SB-6000 will seal and enhance the beauty of new and old surfaces with a luxurious, wet look sheen with pronounced color enhancement and satin finish. It is breathable and will not trap naturally occurring efflorescence, allowing it to be applied immediately after new paving stones are installed. SB-6000 improves surface durability and freeze-thaw resistance while protecting the surface from salt, acid and staining. It exceeds all VOC, EPA and OSHA standards. SB-6000 Wet Look Sealer has the consistency of water and is milky white when applied; it dries to a clear, wet look on the surface of the pavement. SB-6000 Wet Look sealer can be used both inside and outside on old and new pavements. Cured sealer is freeze resistant to -60°F (-51°C) and is stable up to a temperature of 180°F (82°C).
Ideal for concrete and clay pavers, flat and stamped concrete, or natural and manufactured stone. Also suitable for masonry, retaining walls, porous or unglazed tile and terrazzo. Not recommended for marble, granite or ceramic tile.
A test area is always recommended to determine product suitability and compatibility with your specific surface before use and also if desired results are achievable. Due to the inherent variabilitity of natural stone and clay products, long term performance may vary. Please consult with us prior to sealing if there are concerns.
|Pavers & Other Hardscape Surfaces||100 – 200||9.3 – 18.6|
|Concrete||150 – 250||13.9 – 25.2|
|Retaining Walls & Other Vertical Surfaces||100 – 200||9.3 – 18.6|
Per gallon. Two coats of SB-6000 are recommended. Allow first coat to dry before applying second coat. Second coat coverage is estimated between 200-300 sq. ft. per gallon (18.6-27.9 M/G). Actual coverage may vary depending on the type, age, condition, porosity of the surface, application method and other local conditions such as temperature and humidity.
TEST FIRST on a small inconspicuous area to determine the suitability and if desired results are achievable with this product on your specific surface. The surface should be thoroughly clean and free from oil, dust, loose material, and previously applied sealer other than SB-6000 prior to sealer application. If needed, prepare surface with Surebond Cleaners before sealing. Thoroughly rinse all cleaner residue prior to sealing. Allow surface to dry for a minimum of 24 hours after cleaning and/or rain before sealer application. Use a leaf blower to remove dust, debris and fine sand particles from the surface before sealing. Cover/protect nearby landscape, vehicles and buildings from overspray during application.
Apply when day and night temperatures are between 40°F – 95°F. Avoid windy conditions to keep sealer spray from drifting. NO pre-blending or mixing required. Do NOT dilute. SB-6000 can be applied by spraying or rolling on the surface. Using a handheld garden sprayer or foam roller, spray or roll on one light coat in the same direction over the entire area to be sealed. Once the first coat is dry to the touch (affected by humidity and temperature), spray or roll a second light coat in a cross direction to the first coat. The cross application will ensure a more uniform coverage. Use coverage guidelines to determine a sufficient amount of material to provide on each coat. Enough sealer should be applied to wet down and saturate all the pores on the paver surface, including the chamfers, edges and recessed areas on textured pavers. Care should be taken that no excess sealer is pooled on the surface or in the sand joints of the pavement. If necessary, back roll to remove the excess sealer with a foam roller. Material coverage will depend on the surface porosity and texture. Depending on environmental conditions, a light reapplication may be required every 6 months to 2 years to maintain desired effect. NOTE: Excessive applications can cause surface to become slippery. Application of this product is out of the control of SEK-Surebond. Application steps should be followed completely and accurately. Should a problem occur with this product, SEK-Surebond limits liability to product replacement only. Buyer assumes all risk and liability resulting from the use or misuse of this product.
Surface will be dry to touch within 60 minutes assuming 65-85°F at 50% relative humidity. Low surface or air temperature and or high relative humidity will extend dry times. Protect the surface from dust, rain, condensation and traffic while drying. Area can be open to foot & light vehicular traffic in 24 hours depending on site conditions. Full cure in 7 days under normal conditions.
For tools and equipment, use soap and water before product is allowed to dry.