Surebond 9000 - Solvent Based Wet Look Sealer High Gloss (Sample Pint)

Surebond 9000 - Solvent Based Wet Look Sealer High Gloss (Sample Pint)

Regular price $0.00 Sale


  • Deeply Enhances Surface Tone with Gloss Finish
  • Provides Water, Salt, Stain & UV Protection
  • Promotes Easier Cleaning & Maintenance
  • Breathable, Immediate Application Solvent Based Sealer

SB-9000 Wet Look Sealer will seal and enhance the beauty of new and old interlocking pavers, concrete, masonry and other related surface with a rich, enhanced, wet look and gloss finish. SB-9000 is the perfect product to restore the look of old/tired pavers. The high solids formula combines properties of adhesion, flexibility and UV light resistance to provide a long lasting seal. SB-9000 will penetrate the substrate and provide a protective layer on the surface that is resistant to mild acid, alkali and salt attack. SB-9000 will increase the stain resistance of the surface to allow for easier cleaning, maintenance and extended wear. SB-9000 can be applied immediately after paver installation, as it is breathable and will not trap naturally occurring efflorescence and moisture. SB-9000 is a solvent based product and is clear in appearance when applied.  SB-9000 is designed as a one-coat application but a second coat may be applied if desired. Cured sealer is freeze resistant to -60°F (-51°C) and is stable up to a temperature of 180°F (82°C).

Suitable Surfaces

Ideal for concrete and clay pavers, flat and stamped concrete, or masonry surfaces such as stucco, retaining walls, concrete walls and exposed aggregate. Also works on limestone, sandstone and natural paving stones.

A test area is always recommended to determine product suitability and compatibility with your specific surface before use and also if desired results are achievable.  Due to the inherent variabilitity of natural stone and clay products, long term performance may vary. Please consult with us prior to sealing if there are concerns.


Concrete & Clay Pavers/Exposed Aggregate 250 – 300 23.2 – 27.9
Cast-In-Place & Precast Concrete 200 – 300 18.6 – 27.9
Limestone & Sandstone 150 – 250 13.9 – 23.2
Old Concrete 300 – 400 27.9 – 37.2


Per gallon. Two coats of SB-9000 are recommended. Allow first coat to dry to the touch before applying second coat. Second coat coverage is estimated between 350-400 sq. ft. per gallon (32.5-37.2 M/G). Actual coverage may vary depending on the type, age, condition, joint size and porosity of the surface, application method and site conditions such as temperature.


TEST FIRST on a small inconspicuous area to determine the suitability and if desired results are achievable with this product on your specific surface. The surface should be thoroughly clean and free from oil, dust, dirt, loose material, and previously applied sealer other than SB-9000 prior to sealer application. If needed, prepare surface with Surebond Cleaners before sealing. Thoroughly rinse all cleaner residue prior to sealing. Allow surface to dry for a minimum of 24 hours after cleaning and/or rain before sealer application. Use a leaf blower to remove dust, debris and fine sand particles from the surface before sealing. Cover/protect nearby landscape, vehicles and buildings from overspray during application.


Apply when day and night temperatures are between 40°F – 95°F. Avoid windy conditions to keep sealer spray from drifting. NO pre-blending or mixing required. Do NOT dilute. Apply by airless sprayer, hand held (pump-up) sprayer, or short nap (solvent resistant) roller. Sprayer/equipment should be of solvent resistant design with neoprene or Viton type fittings. Hold sprayer nozzle perpendicular to the surface and overlap each coat. If spray and back-roll application is used, use a short (1/4”) nap, solvent resistant roller IMMEDIATELY AFTER SPRAYING as the product dries quickly. Short nap will ensure even application. If applying by roller only, it is advised to constantly maintain a wet edge, and to keep the roller wet with sealer resin to avoid potential lap marks or surface mottling upon drying. Do not roll back and forth excessively, as this may cause excessive bubbling. Re-rolling immediately after film starts to become tacky can cause the roller to become stringy. SB-9000 is designed for a two-coat application with the second coat to be applied only after the first coat has dried to the touch. NOTE: Excessive applications can cause surface to become slippery. Application of this product is out of the control of SEK-Surebond. Application steps should be followed completely and accurately. Should a problem occur with this product, SEK-Surebond limits liability to product replacement only. Buyer assumes all risk and liability resulting from the use or misuse of this product.

Dry Time

Surface will be dry to the touch in 20-30 minutes assuming 65-85°F. Low surface or air temperature will extend dry times. Protect the surface from dust, rain, condensation, and traffic while drying. If dry, area can be open to foot & vehicular traffic in 24 hours depending on site conditions.

Clean Up

For tools and equipment use xylene or toluene.


Welcome to the Loyalty Points Demo Store :-)

Sign up and receive 5000 pts to test out in our Store.

Earning and redeeming Reward Points

Earns you
Redeems to

Ways you can earn

  • Product Purchase
  • Refer a friend
  • Share on social media

Learn more about our program

Net Orders Checkout

Item Price Qty Total
Subtotal $0.00

Shipping Address

Shipping Methods